SAMSUNG SCX-4300 |
Www.ereset.com/samsung-clp/fix-firmware-reset-samsung-clp-320-325-n-w-k-cip-clt-407/ CLP310 CLP315 N/W http Of course this won't fix the worn out part but often the warnings are premature. If your printer is the C460FW which has a number pad keyboard then this method probably won't work.
The SAMSUNG SCX-4300 is small, yet powerful. Despite its diminutive 16.00″ x 14.25″ x 9.10″ dimensions, it cranks out 600 x 600 dpi documents at a rate of 19 ppm. It also has a monthly duty cycle of 10000 pages. The SCX-4300 is versatile, too, with ID Card, Auto Fit, N-up, Clone and Poster copy modes. And a rich matte black finish gives a contemporary feel to your workplace. With the SAMSUNG SCX-4300, it’s not hard to imagine. But how to ResetCounter for it? Here’s it
1. First, download below tool as RAR and extract compressed file.
2. Run fix.bat and get an Command Line Screen, Press Enter. You will get FIX_SCX4300_V1.13_Fact_romdl.hd
2. Run fix.bat and get an Command Line Screen, Press Enter. You will get FIX_SCX4300_V1.13_Fact_romdl.hd
- Press <MENU><COPY><LEFT><RIGHT><MENU><RIGHT> LCD show TECH
- Press <MENU> again, LCD show DATA SETUP
- Press <OK> and <RIGHT> until LCD show FLASH UPGRADE -> Select LOCAL and Press <OK>
Notice: If your printer ‘s not responded for long time you can turn it off and on again. You can have to re-install printer driver for it.
- Press <MENU><COPY><LEFT><RIGHT><MENU><RIGHT> LCD show TECH
- Press <MENU> again, LCD show CLEAR COUNTERS -> CLEAR ALL CNT -> <OK>
- Wait for RED light is on and turn off your printer.
5. And now use a pickup tool or what thing in your hand remove counter chip on toner cartridge out. It’s OK now!
Now good luck and anything else please comment here!
Download Reset Counter for SCX-4300
SAMSUNG ML-1660 |
Now I have not gotten any Samsung ML-1660, but I have method to reset page counter Samsung ML 1660 for you. So that, you must to do this with your own risk. Remember, don’t turn off your printer when reflashing. Try as below:
2. When download completed, unzip it and you will get two files usbprns2 and FIX_ML-1660_v.82.00.78
3. Make sure that your printer connected to your computer completely.
4. Drag and drop file FIX_ML-1660_v.82.00.78 to usbprns2
5. Wait for reflash until green light is on. Don’t turn off your printer when reflashing. Light will go RED to ORGAN and GREEN, just wait!
And congratulation! Your printer have been resetted
PS: There’s a new method but it’s not tested. You can try it:
- Cover Vcc pin on Toner Chip with tape
- Put you cartridge into printer and turn it on.
- Red light will be on, but you can print out normally.
- Put you cartridge into printer and turn it on.
- Red light will be on, but you can print out normally.
Try it and Good luck!
SAMSUNG ML-2510 |
You can try this:
- You should purchase a reset fuse with 250mAh and 3/4″ inch long (20 mm) round glass with metal ends like this.
- The electrical contacts are not in the cartridge but inside the printer: There is a plastic fuse holder on the cartridge, even the starter cartridge. You just simply pop it into the holder. This will stop the flashing red LED and the system tray will say the cartridge is full.
This way is applied to refill toner cartridge.
Reset Page Counter for Samsung ML-1660
SAMSUNG ML-1640 |
Samsung ML-1640, a compact and cheep price and suitable for home and small office, has a starter Toner Cartridge can print maximum about 700 pages. It’s very easy to refill but it will make you mad sometimes when red light is on. So what’s happen? Samsung (maybe me if I made it ) don’t like customers refill tone cartridge so they placed a counter chip on mainboard. If you are an technican, it will be very easy (how to do, I will post up later). There many of articles about how to reset Samsung ML-1640, but I think almost of its are all fail because Samsung has changed Counter Chips and Firmware (from .83 to .93). After a long time I have resetted alot of Samsung ML-1640, I wanna give to all this tool. All free!
This tool has two batch files have been named step1.bat and step2.bat to make all thing become easy. Everything you need have just do step by step as Readme.txt and wait for self reflashing routing active.
How to check firmware version?
- Turn on your printer (red light still on).
- Press and hold down until data light on.
- Your printer will printe out self test page. Read carefully to find out what’s your firmware version. Good luck!
Warning:
- Do it with your own risk.
- Don’t turn off printer when reflashing.
Note:
- If red light still is on, you can turn of your printer and start to reflash from begin.
![Free Free](/uploads/1/2/5/7/125769277/193014404.jpg)
- If you can not make anything better, go to Samsung website and download reflash tool (ML1640_V1010083.exe) to reflash it back to very first firmware version.
Download here
Reset Samsung All-in-One SCX-4521F
SAMSUNG SCX-4521F |
1. Press MENU # 1 9 3 4 in sequence rapidly. The LCD panel should now display TECH.
2. Press MENU, and then press ENTER. The LCD panel will display Tech Mode.
3. Press the left arrow (<) button once. The operator panel will display NEW CARTRIDGE.
4. Press ENTER. The operator panel will display [YES].
5. Press ENTER. The toner warning message should be gone.
6. To exit TECH MODE, press MENU # 1 9 3 4 in rapid succession, as if you were dialing a phone number. The operator panel should no longer display TECH.
If problem persists, there may actually be a problem with either the toner cartridge or the SCX-4216F.
It works for SCX-4521F
Firmware Samsung SL-M2070 Review:
– Product name:Firmware Samsung SL-M2070, Samsung SL-M2070 Reset Software.
– Version: 08f, 16f, 20f
– Compatible models: Samsung SL-M2070
– Functional: Removes permanently the Samsung SL-M2070 pages counter limit, Disables errors around toner cartridge which displayed on Samsung SL-M2070 status(Or popup on computer windows): Toner low, install new toner cartridge, toner life end, replace new toner cartridge, toner empty, toner exhausted…Makes Samsung SL-M2070 printer to work without toner chip.
– Version: 08f, 16f, 20f
– Compatible models: Samsung SL-M2070
– Functional: Removes permanently the Samsung SL-M2070 pages counter limit, Disables errors around toner cartridge which displayed on Samsung SL-M2070 status(Or popup on computer windows): Toner low, install new toner cartridge, toner life end, replace new toner cartridge, toner empty, toner exhausted…Makes Samsung SL-M2070 printer to work without toner chip.
How to Reset Samsung SL-M2070
– Before you continue with the reprogramming of the firmware, please make sure that the device is installed on your computer.
– It is very important that under no circumstances should you remove the chip from the cartridge while reprogramming the firmware. After you have succesfully reprogrammed the printer, remove the chip from the cartridge and store it somewhere safely (the chip – a key). In all cartridges which you are going to use in the printer, the chip has to be either removed or sealed. If you have accidently inserted a new cartridge without removing the chip, the device will be blocked. In order to unblock it, you can use the stored chip as a key which help you to unblock the printer.
– And make sure that any other devices (except mouse and keyboard), which are connected to your computer via USB or LPT ports are disconnected. It’s preferable that the computer is connected to the “UPS” (uninterruptible power source) device, because if during the reprogramming process the electricity source has any interruptions, then the reprogramming will be carried out with an error, which makes the device unable to work.
– This firmware will be installed directly to your printer. Before opening firmare make sure that printer is turned on and connected to your computer and printer drivers are installed correctly.
– Be aware that with the reprogramming of the firmware the manufacturer’s warranty goes lost!!
1. Connect the printer to the computer by usbcable and install it.
2. Install Microsoft .NET Framework Version 2.0 program (only for OS older than Windows 7)
3. Set Plugin ClickOnce for your browser (Internet Explorer supports by default)
Plugin for Google Chrome
Plugin for Firefox
4. Click on link, which you get after payment for firmware
2. Install Microsoft .NET Framework Version 2.0 program (only for OS older than Windows 7)
3. Set Plugin ClickOnce for your browser (Internet Explorer supports by default)
Plugin for Google Chrome
Plugin for Firefox
4. Click on link, which you get after payment for firmware
5. After it firmware download begins (downloading time is about 2-4 min depend of internet)
6. Wait until the printer reprograms (1-3 min) and restarts ( if indicator blink that’s mean that printer start reprograming)
7. After that the reprogramming process is finished, restart the printer
Warning! Firmware will be available for installation only for 6 hours! So please make sure you will be able to install firmware during 6 hours before ordering it!
![Samsung toner cartridges Samsung toner cartridges](http://www.dealingwithwindows.com/wp-content/uploads/2011/02/Netframework-version-4.png)
Firmware Samsung SL-M2070 : $25 USD
Your browser does not support JavaScript! Please enable Javascript.
Samsung SL-M2070 toner cartridge/toner chip review:
– Samsung SL-M2070’s cartridge is enclosed with a toner chip that was used to calculate toner coverage and to deliver bold or light printout quality depending on printer original printout design.
– Samsung SL-M2070 toner chip contains calculated limitation that was managed by Samsung manufacturer. Following Samsung, if toner coverage is 5%, Samsung SL-M2070 toner chip is delivered 1.000 – 1.500 pages.
– If toner coverage is higher than 5% -> Toner Page Yields are less than “1.000 – 1.500″ pages. If toner coverage is lower than 5%, Toner Page Yields are “1.000 – 1.500″ pages. That is the reason why bold printouts (high toner coverage) will make printer run out of toner quickly.
– When Samsung SL-M2070 toner chip overload its calculated limitation, printer will be locked inspire of high toner cartridge.
When Samsung SL-M2070 needs to clear page counter limit:
– Samsung SL-M2070 printer’s messages: red light or red light(with Monochrome function printer) blinking(with Multifunction printer), imprinting.
– Computer’s messages: Toner low, install new toner cartridge, toner life end, replace new toner cartridge, toner empty, toner exhausted…
Fix Samsung SL-M2070 with above errors:
1. Change new Samsung SL-M2070 toner cartridge:
– Samsung SL-M2070’s toner cartridge (Samsung MLT-D111S) costs $50 – $60 depending on its supplier and manufacturer.
– Changing toner cartridge seems to be suboptimal because when printer runs out of toner, we also need to change new toner cartridge => money wasting.
2. Change new Samsung SL-M2070 toner chip:
– Samsung SL-M2070’s toner chip costs $6 – $10 depending on its supplier.
– Changing toner chips seems to be more optimal but when printer runs out of toner, we also need to change new toner chip.
3. Clear Page Counter Samsung SL-M2070 by using firmware:
– Samsung SL-M2070’s reset software costs $25 USD => money saving
– Reset software automatically impacts to printer firmware so printer ignores paper counter. Therefore, there is not necessary to change toner chip, you just refill toner when it runs out.
Buy Firmware Samsung SL-M2070 : $25 USD
Your browser does not support JavaScript! Please enable Javascript.
Video reset Samsung SL-M2070 with USB Cable
Video reset Samsung SL-M2070 with Network Access
5 (100%) 1 vote